Automatic Cable Accessories*

Lambretta or Vespa Emergency Cable Repair Kit Set for All Standard and Sports Types. Consists of: 1 x Clutch / Front Brake / Rear brake cable inner...

Cable - Cable Nipple - Quick Action Throttle - Flush - 5.5mm

Tool - Cable Puller - With Thumb Lock Pulls Cables and Slides NippleThird Hand Suitable for all cables As used on the following, Auto scooters Mot...

Vespa - Cable - Clutch Cable Adjuster + Stainless Steel Nut - Genuine - 4cm Long M5 Cable Adjuster, longer 4cm type Genuine Piaggio Part Can als...

Cable Cover - Packet 1.5 metre 6.2mm internal diameter (can be used on thicker cables buy wrapping around) Chrome Effect

Cable - Cable Adjuster - M5 For Vespa Front Brake / Clutch / Gear  

Cable - Cable Adjuster - M7 For Lambretta Gear / Clutch or Vespa Rear Brake.

Dellorto Carburettor Cable Adjuster with 90 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Cable - Cable Adjuster and Nut - M5 - Polished Stainless Steel For Vespa Front Brake / Clutch / Gear Thread size = 5mm Total Length, tip to ...

Cable Nipple - Split Barrel Nipple - Fits over pear shaped cable ends. Fits into Clutch lever / Front Brake Lever All Models of Lambretta and Vespa...

Cable Cover - Packet 1.5 metre x 5mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue or Yellow - Glossy (ca...

Brake Light Switch - Front or Rear Compression Switch - Inserts Into Outer Cable How to fit to a scooter that does not normally have a front brake ...

Cable Cover - Packet 1.5 metre x 6.2mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue, or Purple metallic e...

Cable - Cable Nipple - Standard Throttle Pulley - 5.5mm BOLT HEAD(S2/B4) SCREW HEAD(S2/B5)

Allen Key 3.5mm Suits Lambretta cable Trunnions A (J3-E7)

Cable Cover - Packet 1.5 metre x 5mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue or Yellow - Glossy (ca...

Cable Cover - Packet 1.5 metre x 6.2mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue, or Purple metallic e...

Cable Cover - Packet 1.5 metre x 6.2mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue, or Purple metallic e...

Cable Cover - Packet 1.5 metre Length 10mm internal diameter (can be used on thicker cables buy wrapping around) Suitable for speedo cables. ...

Cable Cover - Packet 1.5 metre x 5mm Internal Diameter (can be use on cables around this thickness) Available in Red, Blue or Yellow - Glossy (ca...

Cable - Cable End Caps Dimensions: 5mm inside diameter, 10.5mm long

Adjustable Cable Nipple - Thin 4mm - Ussually slots into the Carburettor pulley arm - 4mm Attaches to the throttle inner cable.

Cable - Small Cable Top Hat ID 6mm OD 7mm Total Length 9mm Locates the clutch and front brake outer cables into the headset base.

Lambretta - Clutch or Gear Cable Adjuster Screw And Nut - Stainless Steel - All models Page 16 - Parts 25 + 26

Cable Nipple - PK Split Barrel Nipple For Vespa PK with original Plastic/Nylon type Levers fitted. If Chrome or Dog leg levers have been fitted ...

Dellorto Carburettor Cable Adjuster with 70 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Cable - Cable Nipple - 3mm x 3mm Slide Nipple - Requires Soldering - Inside hole is tapered at one end to prevent the solder from pulling through....

Cable - Cable Nipple - Standard Throttle Pulley - 5.5mm BOLT HEAD(S2/B4) SCREW HEAD(S2/B5)

Cable - Small Cable Top Hat ID 7mm OD 8mm Total Length 13mm Locates the clutch and front brake outer cables into the headset base.

Cable Barrel Nipple - M5.5mm diameter x 6mm wide - Solder on Ussually used for Throttle or Gear pulley.

Universal Outer Cable For Clutch / Front Brake / Throttle/ Gear Sold Per Metre - Please amend quantity to length required (eg 1x = 1mtr., 2x = ...

Cable - Cable Nipple - Short Trumpet/Pear - Brass Solder On 5mm Long x 10mm Trumpet With 2mm Hole

Dellorto Carburettor Cable Adjuster with 50 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.