Lambretta Engine All*

Lambretta - Kick Start Shaft Plunger And Pin - All Models Page 4 - Parts 11 and 12

Lambretta - Kick Start Large Return Spring - All Models Page 4 - Part 16

Lambretta - Kick Start Lever - Chrome - All Models Page 4 - Part 19 and 3

Lambretta - Barrel / Piston And Head 185cc Conversion Kit, with very tidy inlet, outlet and transfer ports.Excellent value and performance small bl...

Lambretta - Kick Start Shaft - Li, SX, TV Shaft length 66.5mm Page 4 - Part 15

Lambretta - Kick Start Lever And Bolt - Series 1 and 2 Chrome Page 4 - Parts 19 and 3

Lambretta Chain Tab Washer All Models Page 3 - Part 30

Lambretta - Crankshaft Flywheel Side Woodruff Key 4mm x 6.5mm Page 2 - Part 15 Only large one supplied for lambretta. Picture for illustration purp...

Lambretta - Chain Case Stud Kit As pictured 14 x M6 Studs/Nuts and Spring Washers 14 x M6 Dome Nuts 2 x M8 Studs/Nuts and Spring Washers  

Lambretta - Kick Start Return Plate/Ramp - Li, SX Bolts into Chaincase Side with 3 x M6x20 bolts. Bolts available seperately Page 4 - Part nu...

Lambretta - Race Chain Tensioner Double Life Nylon Block - When the eventual onset of wear occurs, the block can be rotated 180 degrees. Pull down...

Lambretta - Outer Clutch Sprocket / Crown Wheel 46 Tooth - GP 125cc and GP 150cc Solid type for brass bush fitting. Page 3 GP - Part 17

Lambretta - Clutch Arm - Polished Stainless Steel - All Models Page 3 Gp - Part 2

Lambretta - TV 175cc Piston Kit For use with series 1 + 2 Long type con rod. Standard Size 64mm Page 2 - Parts 16 to 19

Lambretta - Kick Start Rubber - Series 1 and 2 Large Cut Out type as shown in picture

Lambretta - Clutch - Clutch Arm Spring - All Models Stainless Steel

Lambretta - Kick Start Shaft External Shim - All Models 1mm Thick Page 4 - Part 18

Lambretta - Kick Start Plunger Spring - All Models Page 4 - Part 13

Lambretta - Standard Clutch Plates - All Models Four Cork Plates. Indian Brand. Page 3 GP - Part 15  

Lambretta - Rear Brake Cable Holder - All Models Page 16 - Part 38

Lambretta - Shim For Gear / Clutch / Brake Arm - All models 12mm x 18mm x 1mm. Page 3 Li - Part 5

Lambretta - Standard Clutch Plates - Surflex Brand - Li, SX, TV, GP, All Models Four Cork Plates.

Lambretta - Barrel Holding Stud - M8 3/8 Whitworth 16 Gauge one end (16mm Long), M8 Shank in the middle (124mm Long), M8 the other (26mm Long). Pr...

Lambretta - Standard Barrel Holding Stud - M8x160mm Price per one. Page 1 - Part 11

Lambretta - Flywheel - Cowling - GP Style - Polished Stainless Steel Suitable for Lambrettas Series 1/2/3 and GP Standard Shallow Depth of ap...

Lambretta - Kick Start Lever - Series 2 with Series 3 Li/SX Chain/Crank case side fitted- Often refered to as Series 4 Chrome Has longer kick...

Fastener - Hexagon Flange Nut - Copperized Exhaust Flange Nut - M7x1mm Pitch Exhaust nut for Gilera 180, DNA 125/180, Piaggio 125/180, Hexagon, ...

Lambretta - Gearbox Main Shim 1.5mm Thick for Special Shimming Page 4 - Part 21 1.5mm Thickness - ( Standard shim is 2mm )

Lambretta - Chain Case Side Kick Start Return Buffer All Models Page 1 - Part 33

Lambretta - Engine Mount Single - Li Requires 2 - Price each. Page 1 - Part 9

Lambretta - Gearbox Selector Sliding Dog - All Models Page 4 - Part 29

Lambretta Competition 185cc Piston Kit - 64mm with Thin 1.5mm chrome rings For use with Li or GP series three crankshaft. Oversizes available on re...