Automatic Carburettors and Spares*

Cable - Cable Nipple - Quick Action Throttle - Flush - 5.5mm

Dellorto Carburettor Cable Adjuster with 90 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Cable - Cable Nipple - Standard Throttle Pulley - 5.5mm BOLT HEAD(S2/B4) SCREW HEAD(S2/B5)

The carb caps from Crazy Monkey Development are a massive step forward.They replace your existing carb cap and the throttle cable is not just perfe...

Dellorto 4 Sided Float Needle For Modern Ethanol Fuel Standard Lambretta, Vespa Large Frame, Vespa Small Frame. For Dellorto, Spaco, Jetex Carbur...

Adjustable Cable Nipple - Thin 4mm - Ussually slots into the Carburettor pulley arm - 4mm Attaches to the throttle inner cable.

Dellorto Gasket Set for PHBH Carburettors

Carburettor -  30mm PHBH Dellorto - Two Stroke Carb. Lightweight Alloy Left hand side idle screw fitment as standard ( viewing from the front of t...

Carburettor Cable Choke Assembly For Dellorto PHBH/VHSB/PHBL/VHSA/PHBE Carburettors

Dellorto 4 Sided Float Needle Red Tipped, Spring/Sprung Type Si 20-24mm + Various Dellorto's Fits needle valve seat sizes 150,170,200 and 225. N...

Cable - Cable Nipple - Standard Throttle Pulley - 5.5mm BOLT HEAD(S2/B4) SCREW HEAD(S2/B5)

Cable Barrel Nipple - M5.5mm diameter x 6mm wide - Solder on Ussually used for Throttle or Gear pulley.

Dellorto Carburettor Cable Adjuster with 70 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Cable - Cable Nipple - 3mm x 3mm Slide Nipple - Requires Soldering - Inside hole is tapered at one end to prevent the solder from pulling through....

Carburettor - Bellmouth - Short 16mm - Plastic Screw on 42mm fitting - 16mm Total Length For Dellorto PHBH 28 and 30mm or similar

Carburettor - Dellorto - PHBL 25 Rubber Mount not included. Choice of Cable or Flip Choke. Whats fitted in the carb, correct as 09/11 PHBL25 AQ26...

Dellorto Carburettor Slide Needle Clip.

Dellorto 4 Sided Float Needle Spring/Sprung Type Si 20-24mm Fits needle valve seat sizes 150,170,200 and 225. Not suitable for seat sizes 250 an...

Carburettor - 28mm  PHBH Dellorto - Two Stroke Carb. Lightweight Alloy Left hand side idle screw fitment as standard ( viewing from the front of t...

Dellorto Carburettor Cable Adjuster with 50 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Carburettor - Mixture Screw Kit For Dellorto Carburettors Models PHBE PHB PHBH PHBL PHF PHM VHB VHST As Pictured

Dellorto Gasket Set for PHBL Carburettors

Dellorto 3 Sided Float Needle Vespa Small Frame 16mm carbs Various Small Dellorto's Part Number:2838

Cable - Cable Nipple - Short Trumpet/Pear - Brass Solder On 5mm Long x 10mm Trumpet With 2mm Hole

Cable Barrel Nipple - M5 x 7.6mm - Solder on

Malossi Carburettor Cable Adjuster with 180 Degree Elbow. Thread: 6mm at carb end, 5mm on the adjuster Suits most carburettors.

Carburettor - Bellmouth - 55mm - Plastic Screw On 42mm fitting - 55mm Total Length For Dellorto PHBH 28 and 30mm or similar

Carburettor Rubber Mount To suite: Amal Dellorto VHSA 30 / 32mm Mikuni TMX 32mm, 35mm 39mm Inside Diameter. Uses 32mm to 50mm Hose Clamp

Carburettor - 26mm PHBH Dellorto - Two Stroke Carb. Lightweight Alloy   Left hand side idle screw fitment as standard ( viewing from the front of ...

Carburettor - VHSB 34mm Dellorto Flat Slide Whats fitted in the carb, correct as 09/11 VHSB34LD 34 Idle Emulsion Tube DP266 atomiser/air corrector...

Race Carburettor - 30mm Dellorto Flat Slide VHSH Uses standard PHBH Rubber Mount (34mm inside diameter). Usual standard make up: Main Jet: 175-180 ...