Vespa Flywheels & Stators*

Vespa Stator Plate Lighting Coil for 12 Volt AC Lighting The four lighting coils are wired in series. Starting at Coil Number 1 which has its in...

Vespa - Condensor - V50, V90, V100, Primavera, Super, Sprint, Old Vespa Two Wire Condensor - Also fits One Wire Type. 2cm diameter - Total 3.2cm Ta...

Vespa BGM Stator Plate - PX,PE, EFL and Disc Electronic 120W This stator plate can be modified for use on the P200E by changing the white terminal ...

Vespa - Points - V50/90/100/Primavera/Super/Sprint/GT/Old Vespa Points including centre pin. For Your Information: Same points as the Older ...

Vespa - Wiring - From Stator To Loom Connector Block Stator plate wiring block Male Uses 2.1mm female bullet connectors SAP-TL-068

Vespa - Connector Block for Wiring Loom Fitted to the Main Wiring Loom Connects loom to the Stator Plate - PX, T5 Female - Four Hole Requ...

Vespa - Flywheel - Lock Washer Sold individually PX, PE, PX Disc, T5, T5 Classic, LML, PK xl

Vespa - Condensor - V50, V90, V100, Primavera, Super, Sprint, Old Vespa Single Wire Type. Please ensure you state which model you require the...

Vespa - Points without Centre Pin - V90, Prim, Super, SS180, Old Vespa The Centre Pin for Contact Points in the 50's and early 60's was screwed...

Beedspeed Vespa 12 VOLT Electronic Conversion Stator Plate for use with beedspeed electronic flywheel - Super, Sprint, Old Vespa New Mark 2 Type wi...

Vespa - Condensor - P125X, P150X, V100 Sport Same as Original Part No. 182343

Vespa - Points - P125X, P150X, V100 Sport Genuine spare part - EFFE Brand Also fit the Italian and Indian Lambretta Series 3

Vespa - Points - Old Vespa, G150, GS160, SS180, SPORTIQUE, 1SUPER, 52L2. For Your Information: Same points as the V50 / Primavera / Super / Spr...

Vespa Electronic Stator Plate Low Tension Ignition Coil for PX / T5 / PK / Cosa. Fits standard 11mm tall laminates. 12mm and 13mm hole sizes ...

Vespa - Points - V50 Special

Vespa - Wiring - From Stator To Loom Connector Block - Female Stator plate wiring block Six Hole - Three holes used on PKS, PKXL and Five on electr...

Electronic Stator Plate Pick up Unit for Lambretta or Vespa Manufactured by BGM

Vespa - Stator Plate Body/Base Plate Bare - Electronic Type Super, Sprint, VBB, Old Vespa with 12V electronic kit fitted. Pre Slotted for fix...

Vespa PK - Wiring Sleeve For the Stator Plate Wires and External Connector Block - Stator Plate to Main Frame Loom Wiring. Easy Fit Type. There is ...

Vespa - Points - Old Vespa/GT Listed as suitable for, Vespa 125 VNB4T VNB5T VNS4T Vespa GT VNL1T Vespa GL 150 VLA1T Old Vespa, G150, GS...

Vespa LML Electronic Stator Plate Low Tension Ignition Coil. Fits standard 12mm tall laminates. 11mm and 13mm hole sizes are available for co...

Vespa Electronic Stator Plate for PX, PX EFL, PX DISC Quality Product by RMS of Italy. This stator plate can also be used on the P200E models by ch...

Vespa - Condensor - Filso Single Wire Type. For Spainish Filso Models

Vespa - Points Point including centre pin. Made in Italy by EFFE and OEM quality. Listed as suitable for 50cc Ape CBA Ciao Bravo...

Vespa - Points - Ape Point including centre pin. Made in Italy by EFFE and OEM quality. Listed as suitable for Piaggio Vespa Ape Mp 550 ...

Vespa - Points - Spainish Filso Point

Vespa - Points - 6 Pole Standard Suitable for - Vespa P125X, P150X, V100 Sport - Lambretta Series 3 6 pole Italian and Indian

Vespa PK - Wiring Sleeve For the Stator Plate Wires and External Connector Block - Stator Plate to Main Frame Loom Wiring. Stator Plate Wiring Sle...

Stator Plate HT Coil - Internal Type Two Wire Type Pin Distance 43mm VNA/VNB1T, with battery for Vespa 125VNB4-5 1 wires red, 

12 Volt AC Lighting Conversion Coil Set. Converts all Older Vespa 6 Volt Three Coil Stator Plates to 12V. Fits all V50, V90, V100, Prim, Super, Ra...

Electronic Stator Plate Pick up Unit for Four Pole Stator Plates not UK Six pole. PK XL Rush Model and other PK none UK European models. Usual ohme...

Vespa - Stator Plate Ignition Low Tension Primary Coil - Femsa - Rally 200

Vespa Stator Plate Pick Up Unit - Femsa - Rally 200 Set up information - Air Gap Pick up to Cam = .25mm to .3mm