Oil Measure Jug 100ml Same as Original Part No. 085058
STEERING NUT RING SPANNER Made from 304L Stainless steel, will last a lifetime.
Beedspeed Timing Disc in Degree's with Timing Instructions Alloy Disc 16.3cm Diameter with 1.3cm Centre Hole . Link to Lambretta and Vespa Ti...View full details
Traveler - Oil Measure/Mixture Bottle with Screw on Cap - Polini - 250ml - 1% 2% 3% 4% 5% 6% and 7% Markings
Tool - Cable Puller - With Thumb Lock Pulls Cables and Slides Nipple Suitable for all cables As used on the following, Auto scooters Motorcycle Ca...View full details
Oil Measure/Mixture Bottle with Screw Shut Easy Squeeze Top ('Squeeze Fuel-Oil Dispenser') A new cleverly designed oil mixture bottle, an indispen...View full details
STEERING NUT C SPANNER 37mm
Lambretta Clutch Holding Tool Sits on the Lambretta clutch spider with the handle between the spaces in the crown wheel... locking the clutch spide...View full details
Lambretta Engine Mounting Removal and Fitting Tool E (J3-K8)
Tool - Piston Locking Tool - 14mm
Tool - Oil Measure Jug And Cap 100mls B (J3-C6)
Lambretta Rear Hub Puller For Series 3 3 Hole, 7mm Bolts C (J3-J10)
Lambretta Rear Hub Puller - Heavy Duty For Series 3 3 Hole, 7mm Bolts D (J3-K7)
Tool - Lambretta Rear Hub, Drive and Flywheel side bearing drift tool. Vespa PX, Rally, Sprint, T5 - Drive and Flywheel side bearing drift tool. ...View full details
Lambretta - Plug Spanner
Tool - Tyre Levers - Pair - 25cm/10 Inch For all tyres.
Fork Oil Syringe - Capacity 60ml B (J3-C5)
Tool - Oil Can - Pump Action - 1/2 Pint - Suitable for cable lubrication or engine filling. C (J3-A4)
Stainless Steel T-Bars for Lambretta Magneto Flange & Gearbox End Plate Removal
Tool - Lambretta Fork Spring and Rear Shock Compressor E (J3-L7)
Petro Patch Putty - Granville - Heavy Duty - 50gram Granville Petro Patch Putty is a fast acting Epoxy Putty with hundreds of uses around the auto...View full details
Tool - Inner Tube Puncture Repair Kit As pictured, supplied in small green case.
TUBELESS TYRE PUNCTURE REPAIR KIT Kit Consists of: 1x Carry Case 1x Probe 1x Eye Needle 1x Rubber Cement 1x Knife 5x Strip Plugs - Enou...View full details
SPRING PULLING HOOK HEAVY DUTY - Stainless Steel Suitable for Stand / Exhaust Springs etc. 8 Inch / 20cm Long
Tool - Piston Pin Removal Tool - 16mm - Lambretta & Vespa P200/T5
Universal Con Rod Holding Tool, suitable for Lambrettas and Vespas.Laser cut from 304L Stainless Steel, will last forever!
Lambretta Flywheel Holding Tool E (J3-L11)
SPARKPLUG BOX SPANNER 65mm Long with Swivel Arm For 21mm spanner type Plugs such as: NGK AB and B types. such as B8ES, B6HS B (J3-F6)
Lambretta Rear Jack to Replace Spare Wheel B (J3-L10)
Tool - Lambretta Front Fork Link Bush And Buffer Drift D (J3-J3)
Tool - Lambretta Crankcase Separator Splitter
BATTERY CHARGER - UK 3 PIN TYPE PLUG Selectable ON OFF 6 V or 12 V Charging Voltage. Includes Extra Hook Up Wire that can be left permanently fixed...View full details
Lambretta - AF 6 Plate ROAD Clutch Metal Holding Tool For use with AF Rayspeed 6 Plate Competition Clutch. Not suitable for the six plate Race ...View full details
Spark Plug Hole Mounted / Top Dead Centre Gauge - Fixed Type Screws in or out to stop the piston in the required position. Calibrated around the to...View full details
Tool - Tyre Levers - Pair - 37cm/15 Inch For all tyres.